|
Home
About
Version History
Requirements
Reference
Gallery
Download
Site hosted by:
|
Reference
Use this as a reference. Depending on your cell phone
or mobile device, buttons may vary. The way you access and
navigate around menu options might also differ.
- Operating the timer
- Countdown Modes
- Setting the current time or
countdown time
- Troubleshooting
- Operating the timer
| ST/STP |
|
Starts/stops timing in current
mode. If Record Start times for lap
times is enabled in the Option settings
when you start timing, the current time is added
to the Lap time list. |
| RST/LP |
|
When timer is not
running:
- Resets time to zero in normal timing
mode.
- Resets time to stored countdown start
time in countdown any mode.
When timer is running:
- Records a lap time, adding it to the
list. Lap times are formatted as:
(AA:BB:CC; DD:EE:FF[X])
where AA:BB:CC is the elapsed time since the
last lap time, DD:EE:FF is the current time
on the clock when the lap time was taken,
and X is either + or -, depending on whether
the mode is normal timing or a countdown
mode, respectively. An asterik (*)
will appear next to times that are being
displayed as HH:MM:SS. Otherwise, all
times are displayed as MM:SS:ss.
|
Back to top
- Countdown Modes
Cycle
through the modes by pressing the "FIRE" or "SELECT"
button on your phone. Usually this is the button
at the center of the navigation arrow buttons. The
currently selected mode is always displayed as an icon
(see below) to the right of the LED digits.
 |
|
Normal timing mode. Time
increases as time goes by. |
 |
|
Countdown mode. Time will
decrease as time goes by. When zero time
is reached, the alarm and vibration will go off
according to Option settings. |
 |
|
Continuous countdown mode.
Same as countdown mode except when zero time is
reached, the time will automatically reset to
the stored countdown start time and continue
running. |
Back to top
- Setting the current time or
countdown time
 When you enter an input mode (Set Time or
Set
Countdown), a small black triangle will appear
beneath the currently selected digit. There will
also be a text label showing exactly which input mode
you are in. The controls are:
| LEFT/RIGHT |
|
Move digit selection left or
right. |
| UP/DOWN |
|
Increase or decrease digit
value. |
| FIRE/SELECT |
|
Toggle time display between
HH:MM:SS and MM:SS:ss. Use this to input
times over an hour. |
| 0 - 9 |
|
You can directly type in a
digit to change the selection. Pay
attention to what time display you are using (HH:MM:SS
or MM:SS:ss), since the digit ranges are
different. |
Select OK to save settings or Cancel to
restore previous settings.
Countdown time is stored separately from the current
time on the watch. It is the time that gets
restored when the user resets the time in any
countdown mode.
Back to top
- Troubleshooting
I
can't set the digit I want in Set Time or Set Countdown.
Make sure that you are in the right time display,
HH:MM:SS or MM:SS:ss. Press FIRE/SELECT to
toggle it.
After I set a time in Set Countdown, it disappears
when I hit OK.
This is supposed to happen. The countdown time
you entered does get stored, but it will not affect the
actual time on the clock. When you reset
the time in a countdown mode, the time you entered will
be restored. If you want to change the starting
time, use Set Time.
I took multiple lap times on different Start/Stop
runs and I can't distinguish which is which in the Lap
time list.
This is where the Options setting
called Record Start times in lap times comes in handy.
It will insert the time for whenever you hit the Start
button right into the list.
The Lap time list is full of old times that I
don't want.
Remember to use Reset if you want to clear
the Lap time list. Keep in mind that
everything gets saved when you quit the program, even
the lap times. That means, when you start up the
program, you will have to clear the Lap time list
if you didn't do it before the last time you quit.
Back to top
|
